What Size Chain Fits a Ozito CSE-355 (14" Electric)?
Share
The Ozito CSE-355 (14" Electric) (nullcc, Electric class) runs a 3/8 LP pitch, .050 (1.3mm) gauge chain. Drive-link count depends on bar length (see table). Always confirm the drive-link count on your bar or use the Farm & Acre Co Chain Finder.
Need the right chain for a Ozito CSE-355 (14" Electric)? Here are the exact chain specs for this saw and how to make sure it fits the first time. If you would rather just enter your saw and get the answer, use our free Chain Finder.
Ozito CSE-355 (14" Electric) chain size chart
| Bar length | Pitch | Gauge | Drive links | Chain type |
|---|---|---|---|---|
| 14" | 3/8 LP | .050 (1.3mm) | 52 | Low profile |
Electric class, nullcc. Pitch is the spacing between the drive links and gauge is the thickness of the drive link that sits in the bar groove. You need the pitch, the gauge and the drive-link count all correct for a chain to fit.
The chain we recommend for the CSE-355 (14" Electric)
For the CSE-355 (14" Electric), we recommend our 3/8" low-profile .050 (1.3mm) tungsten carbide. Tungsten carbide holds its edge up to 10x longer than a standard chain (when maintained), so it keeps cutting through dry, dirty Australian hardwood that blunts an ordinary chain fast. Match the pitch, gauge and drive-link count from the table above and you are good to go.
Tungsten carbide chain must be sharpened with a diamond wheel or diamond file. A standard round file will not touch carbide.
How to make sure the chain fits
The safest check is the drive-link count. Lay out your old chain and count the drive links (the teeth that sit down inside the bar), or read the numbers stamped on your bar. Bar length alone is not enough, two saws with an 18 inch bar can take different drive-link counts. If in doubt, use the Chain Finder or send us a photo of your bar and we will confirm it.
Looking for a guide bar too?
Chain size and bar fitment are two different things. A guide bar has to match your saw's bar mount, the stud and slot pattern where the bar bolts on, and that changes between makes and even between models from the same make. Chain size alone does not tell you which bar fits. Before you order a bar, check your saw against our Bar Mount Guide and confirm your bar mount. If you are not sure, send us your saw model and we will confirm it before you buy.
Frequently asked questions
What size chain does a Ozito CSE-355 (14" Electric) use?
The Ozito CSE-355 (14" Electric) runs a 3/8 LP pitch, .050 (1.3mm) gauge chain. Drive-link count depends on your bar length (see the table above). Always confirm the drive-link count stamped on your bar, or use our free Chain Finder.
How many drive links does a Ozito CSE-355 (14" Electric) take?
It depends on the bar length. Common counts for the CSE-355 (14" Electric) are 52 drive links across its standard bar sizes. Count the drive links on your current chain to be sure.
What pitch and gauge is a Ozito CSE-355 (14" Electric)?
3/8 LP .050 (1.3mm). Pitch is the spacing between drive links and gauge is the drive-link thickness. Get both right, plus the drive-link count, and the chain will fit.
Can I run a tungsten carbide chain on a Ozito CSE-355 (14" Electric)?
Yes. We stock tungsten carbide chain in this saw's size. Carbide holds its edge up to 10x longer than a standard chain (when maintained), which suits dirty, dry and hardwood cutting. Match the pitch, gauge and drive-link count and you are set.
Not sure? Send us your saw model and a photo of your bar and we will sort out the right chain. Call 0431 183 421 or email us.